Analyzer Systems in Bengaluru

Measuring transducers MT/UMT 5x0 are intended for measuring, analysing and monitoring single-phase or three-phase electrical power network. They measure RMS value by means of fast sampling of voltage and current signals, which makes instruments suitable for acquisition of transient events. A built-in microcontroller calculates measurands (voltage, current, frequency, energy, power, power factor, THD phase angles, etc.) from the measured signals.Features:Evaluation of the electricity supply quality in compliance with SIST EN 50160Measurements of instantaneous values of more than 140 quantities (U, I, P, Q, S, PF, PA, f, , THD, MD, energy, energy cost by tariffs, etc.)Power accuracy class 0.2Harmonic analysis of phase, phase-to-phase voltages and currents up to the 63rd harmonicRecording up to 32 measurands and 32 alarms in the internal memory (8 MB flash)Measurements of 40 minimal and maximal values in different time periods32 adjustable alarmsFrequency range from 16 Hz to 400 HzUp to three independent communication ports (RS 232/485 up to 115,200 bit/s, Ethernet and USB communication possible)MODBUS and DNP3 communication protocolsRemote display connectionUp to 4 inputs or outputs (analogue outputs, pulse outputs, alarm outputs, tariff inputs)Additional communication port (COM2)Universal power supply (two voltage ranges)Automatic range of nominal current and voltage (max. 12.5 A and 600 VL-N)Adjustable tariff clock, display of electric energy consumption in selected currencyHousing for DIN rail mountingUser-friendly PC MiQen software.Types of measuring transducers: MT/UMT 560 - multifunctional transducer & analyzer MT/UMT 550 - multifunctional transducer & recorder MT/UMT 540 - multifunctional transducer

16700 66407-3842-23-200240-0008-PCB BOARD FOR AGILENT 16702B

WADiana compact analyser offers total automation in immunohematology with safety and flexibility in pre-transfusion analyseProduct features:Fully automated with maximum safety features for continuous and integrated automatic process for incubation, centrifugation, reading and interpretation of results.High on flexibility and adaptability with easy to operate software

The R ZVH is a rugged, handy cable and antenna analyzer, designed for use in the field. Its low weight and simple operation make it indispensable for anyone who needs an efficient measuring instrument outdoors for the installation and maintenance of antenna systems. Installation of antenna systemsMaintenance of antenna systemsEasy operationDocumentation and remote controlInstallation of antenna systems Distance-to-fault measurementsOne-port cable loss measurementsReflection measurementTransmission measurementsBuilt-in DC voltage supplyPosition finding using GPS receiver

The Kibra 480 is a stand-alone protocol analyzer that provides comprehensive bus and JEDEC timing analysis for DDR3 and DDR4. Sitting in-line on a live system, the analyzer uses a proprietary probe implementation to allow loss-less capture of high speed DDR transactions while automatically identifying timing and protocol violations. Overview DDR is the acronym for Double Data-Rate Synchronous DRAM (SDRAM) and is the terminology used to describe memory used on modern computer systems. It is the successor of PC100/133 SDRAM which was primarily used prior to 1999. DDR was first introduced in 2000 and the primary advantage was its ability to fetch data on both the rising and falling edge of a clock cycle, doubling the data rate for a given clock frequency. For example, in a DDR200 device the data transfer frequency is 200 MHz, but the bus speed is 100 MHz. The DDR memory bus runs at the clock rate of 100 MHz for PC1600, 133 MHz for PC2100, 166 MHz for PC2700 and 200MHz for PC3200. However, each DDR memory module and memory chip run at an effective (data) rate of 200 MHz, 266 MHz, 333 MHz and 400MHz respectively. The computer industry has adopted a practical convention of just referring to the data rate as the DDR DIMM speed. So, PC1600 DIMMs are said to run at 200 MHz, PC2100 DIMMs at 266 MHz and so on. Like all PC technologies, memory performance and density continue to evolve to meet the demands of faster CPUs. DDR2 was designed to deliver higher overall throughput, the main difference between DDR and DDR2 DRAM is that for DDR2 the memory cells are clocked at 1 quarter the rate of the bus. DDR2 RAM's bus frequency is boosted by electrical interface improvements, on-die termination, pre-fetch buffers and off-chip drivers. DDR2 RAM memory also uses a new form factor, a 240 pin DIMM (Dual Inline Memory Module) that is not compatible with the DDR1 standard.

This is Current Quality Analyser to analysis the current quality

When time is of the essence, turn to the ABL90 FLEX blood gas analyzer. Designed specifically for demanding hospital wards like the ICU, the NICU and the ED, the ABL90 FLEX analyzer is always ready for the next sample. In just 35 seconds, our cassette-based ABL90 FLEX analyzer can deliver 17 parameters from a sample as small as 65 L. Ensure standardized mixing of your blood samples in only 7 seconds using safePICO syringes and the built-in sample mixer on the ABL90 FLEX analyzer. Compliance is also straightforward when you work with an ABL90 FLEX analyzer. Automatic quality control with dedicated QC solutions comes built-in to the analyzer which also runs continuous system analysis checks, and takes automated corrective actions when necessary.

Basic features The CIR-e analyzer is a programmable measurement unit that measures, calculates and records the main electrical parameters of single and three-phase industrial networks in its memory. We must highlight the following concepts:Serial number: The serial number of CIR-e is an important parameter, since all files generated by the unit must be identified with that number. The 10-digit serial number is written on the rear features label of CIR-e . Programming: The unit is programmed with the setup software CIR-e.exe. The application is stored in the SD card supplied with the unit. In addition, the card records the electrical parameters that are sent to the Web server.Display (in Cir-e Web): The measurement unit includes the right of use of the associated software that is required to handle the energy data of the CIR-e Web application. It is located in a web site that is active 24 hours a day, 365 days a year: http://cir-3.circutor.com.Installation: The analyzer can be installed to analyze balanced (3 wire) or unbalanced (4 wire) single and three-phase networks. The unit must be powered with the auxiliary power supply cables in any of the connection options. The auxiliary power supply wires of the unit are Brown and Green.Measurements: The analyzer takes 128 samples per cycle of the voltage and current variables in true root mean square (TRMS). With all of the samples taken, the unit calculates the arithmetic mean during the recording period selected by the user. The analyzer also records the maximum and minimum values measured during each period. To take these measurements, the analyzer has four voltage sensor inputs and three current sensor inputs.Recording: The unit has a 1 Gb external SD memory, FAT16 format, which stores the parameters measured or calculated by the analyzer. We must highlight the following features: It stores the parameters instantly (measured for a selected period). It stores the maximum and minimum values of the recording period selected. The SD memory can be expanded to 2 Gb. With SD memory of 1Gb the period estimated to register is:Current sensors: The analyzer can work with different models of current sensors. One type of sensor has a single measurement scale. Another sensor model is flexible, allowing the configuration of various measurement ranges. The flexible clamps supplied with the CIR-e analyzer are of the E-FLEX 54 model and can be used with three different scales.More information about clamps in chapter 11. Features of E-FLEX and CP clamps.

Perytons Protocol Analyzer

Spectrometric Oil Analysis Procedure (SOAP) Analyzer

Corona Analyzer Services

Protocol Analyzer System

Chemiluminascense analysers