Electrostatic Coatings

PERMANENT, CLEAR ESD SAFE COATINGersatile, crystal clear urethane coating that adheres to metal, plastic, and most other surfaces. Ideal for converting standard bumpers, bins, tools, and surfaces to ESD safe, saving expensive replacement cost. The end result is compliant with ANSI/ESD S20.20, which prevents static damage to sensitive electronic components.FEATURES BENEFITS Rugged static dissipative coating Surface Resistivity of 10^6 To 10^9 ohms Operating temperature range up to 302 F (155 C) Humidity independent Superior adhesion to variety of surfaces: glass, plastic, etc. Coverage - 1 gallon @ 1 mil wet film will cover ~1600 sq ft, @ 2 mil ~800 sq ft Non-ozone depleting

We are engaged in offering a wide collection of Electrostatic Coatings. With the use of modern techniques, we provide accurate coating service. Our offered services are available in various customized solutions. Apart from this, we are offering this coating service range at the budget-friendly market price. Other details: Highly prompt Timely completionPerfect work As per client need

FABRICATION Steel wires of the required diameter & length are cut and bent to the desired shape and then spot welded to fabricate the required shape of the article. Jigs should be carefully designed to achieve good accuracy, repeatability and desired production rates. The prefabricated article is de-greased, de-rusted, de-scaled, passivated and cleaned. Thin 'wire loops' should be attached at suitable locations, for ease of handling the article, so as not to mar the product appearance. These are later snipped off after the entire operation is over. PREHEATING The bare article is then heated in an oven at 250 -300 C (480-570 F) for 5-10 minutes. The heating time and temperature depends on the mass of the article and the loading of the oven. This has to be practically ascertained to provide the desired production rates and coating thickness. For electrostatic coating lower temperatures may be used. COATING The heated article is dipped in a tray containing the powder and the powder splashed on it, or dipped in a fluidised bed of the powder for 2-5 seconds. The powder will stick to the hot article. Once the article is coated, care should be taken to ensure that it does not rub or come into contact with any surface, to prevent damage to the coating. At this stage, a rough powdery, but uniform coating on the article is obtained. The excess un-melted powder is shaken off with a slight jerky motion or light tapping. The coating thickness increases with the duration of dipping in the powder medium. In electrostatic coating, preheating will give higher build-up. FUSION SINTERING To smoothen out and provide a glossy surface, the article is re-heated in the oven for 2-3 minutes. This causes the powder to melt, sinter and flow out. Excessive heating may cause the coating to dis-colour or sag. The article should be carefully taken out of the oven, without the coating coming into contact with any other surface and allowed to cool in a clean dust free atmosphere. Sometimes water quenching is also resorted to, for wire products. INSPECTION & POST FINISHING The thin 'wire loops', attached earlier for handling the article, are carefully snipped off at the base so as not to mar the appearance. The article is inspected for pin holes or blemishes. These can be filled or repaired with a little powder applied with a small soldering iron or a hot air gun. FUNDAMENTAL NOTES The coating thickness increases with (i) increase in temperature of the article (ii) the thickness of the wire (iii) the duration of dipping in the powder. These parameters have to be practically optimized by "trial and error" to achieve the desired maximum and minimum coating on the thicker and thinner wires of the coated article. A coating thickness of 0.3 to 0.5 mm is normally considered sufficient. It is recommended that the oven should have a circulating fan inside it, to provide uniform temperature, and better heat transfer.

We feel immensely pleased to offer an exclusive array of Auto Coating System. Complete system integration with paint booth feeding, this coating system is designed by using high grade components in compliance with set guidelines under the supervision of skilled professionals. We offer this coating system in diverse customized options to our renowned patrons. Features: High efficiency Increased ProductivityLow maintenance cost Other Details: High Speed OperationControlled painting parameters like DFT, Finish etcIncreased ProductivityLess Per Unit Finishing timeJigging/Figuring to suit product profileBatch type of Conveyorised material handlingComplete system integration with paint booth feeding, baking oven & material handling

Electrostatic coatings

We are renowned Traders of coating

Electrostatic Coating

Our Electrostatic Wall Coatings will protect walls form extreme weather. They are superior in quality and we are well recognized in the industry because of our services. It will give a smooth texture to the wall with an extra fine finishing. Our Electrostatic Wall Coatings is effective to use them as they are user friendly too. Features: Fine finishingNominal pricesAvailable in various colors

Anti Microbial Electrostatic Coating

Electrotype Powder

Powder For Electrostatic Coating

Electrostatic coating

Electrostatic Coatings