Integrated Circuit Device

These products have been sourced from certified and trusted market vendors, who use superior quality raw material and efficient manpower to manufacture the entire range.

TL3842P REG CTRLR BST FLYBK PWM 8-DIP Automotive Transceiver Interface IC Motor Driver IC MOSFET / IGBT Driver Isolation Programmable Logic Automotive / Industrial Sensor Chip Resistor Resistor SMD Ceramic Capacitor Tantalum Aluminum Electrolytic Film SMD / Power Inductor EMI Suppression Power / Signal Transformer Quartz Crystal XO / TCXO Automotive / General Relay Automotive / Board Connector Chip / Wire Fuse ESD / TVS RF / Wireless

This is WiFi serial transceiver module, based on ESP8266 SoC. This is the ESP-01 VariantThis has an integrated tcp/ip stack ESP8266 is a highly integrated chip designed for the needs of a new connected world. It offers a complete and self-contained Wi-Fi networking solution, allowing it to either host the application or to offload all Wi-Fi networking functions from another application processor. ESP8266 has powerful on-board processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during runtime. Its high degree of on-chip integration allows for minimal external circuitry, and the entire solution, including front-end module, is designed to occupy minimal PCB area. The Module Comes with a default AT Firmware. Download the AT Documentation ### This module comes with No Support from us as of the Moment. However There are plenty of Resources Online. So Buy This only if you know what you are getting into ###

Integrated Circuit Device

The HT9170B/D are Dual Tone Multi Frequency (DTMF) receivers integrated with digital decoder and bandsplit filter functions as well as power-down mode and inhibit mode operations. Such devices use digital counting techniques to detect and decode all the 16 DTMF tone pairs into a 4-bit code output.

CD74HC4067 ​​CMOS 16-Channel Analog-Digital Multiplexer Module The CD74HC4067 devices is digitally controlled analog switches that utilize silicon-gate CMOS technology to achieve operating speeds similar to LSTTL, with the low power consumption of standard CMOS integrated circuits. These analog multiplexers/demultiplexers control analog voltages that may vary across the voltage supply range. They are bidirectional switches thus allowing any analog input to be used as an output and vice-versa. The switches have low on resistance and low off leakages. In addition, these devices have an enable control which when high will disable all switches to their off state Features: 2V to 6V operation On resistance: 70 Ohms @ 4.5V 6ns break-before-make @ 4.5V Wide operating temperature range: -55C to 125C

Brand Name- Stonewater High Power 2.1 channel amplifier This versatile and highly reliable 2 stage integrated amplifier produces such detailed output that it puts to shame, many amplifiers that cost much more. The flexibility of 2 ohm stability allows you to comfortably drive anywhere from 2 to 8 speakers. An inbuilt bass amplifier means that you can drive up to two passive subwoofers. This translates to considerable cost savings without compromising on sound quality. A direct USB input means you don't need a separate CD player. The SR-200 is very well suited for medium to large size restaurants, gyms and pubs. Features 2.1 channel operation with Inbuilt active crossoverUSB Player Line out, Subwoofer out Stereo/Mono switch Short circuit protectionOverload ProtectionConvection coolingTamper proof, recessed tone controls Possible configurations 4 Satellites + One passive 12 subwoofer6 Satellites + One passive 12 subwoofer6 Satellites + Two passive 12 subwoofers8 satellites + Two passive 12 subwoofers Specifications System Output (rms):320 W@2 OhmsMinimum Impedance: 2 OhmsDistortion: = 0.05% S/N Radio: = 80db Inputs: USB/SD/Aux/CD/computerMic Inputs: 1 Mics Dimensions: 482x340x88 mm (WXDXH)

Step up the board: use 18650 battery to step up to 9V. Charging board input 5V 1A or 2A to charge the 18650 battery. Battery protection board: over-charge protection, over-discharge protection, over-current protection, over-temperature protection, output short circuit protection. UPS???Uninterrupted power supply??????if input 5V, it will charge the battery and no use the battery power; if power failure, it will automatically use the battery power. Lithium Battery Step Up Module only, other accessories demo in the picture are not included!The four-in-one booster board uses small tips:When using as a UPS, the SW pin should be shorted, the output should be kept in real-time, and the power can be turned off to start the battery at any time.As a mobile power supply, it can be connected to the SW switch, it is turned off when not in use, there is no static loss, and it is very energy-saving.If the SW does not want to connect the switch, it can also be shorted, and the output indicator will be soldered after all the tests are completed. This can reduce the current consumption of ten or twenty mA without affecting the normal output of the circuit and compare the power saving.During the operation, it is possible that the board will enter the protection state and not output due to various reasons (mistakes, misconnections, etc.). After the problem is removed, the board charging port can be connected to the 5V charging, and the board is re-powered. The re-output can be activated.Special usage (very special): If you want to supply 5V to the load when there is external 5V power supply, 3.7V (no boost) for the load directly from the lithium battery when there is no external power supply, you can connect the positive output line of the board directly from the S-pad lead of the SW pin load. Specification: Input Voltage: 5V power supply or 18650 battery (voltage 3.2 to 4.2V)Output Voltage: 9V; Powerless than 5W; Please note the product is not suitable for high power devices.USE 18650 battery onlyModule can charge and discharge at same time, The module step up the battery voltage to constant 9VColor: Green Package includes: 1 x Lithium Battery Step Up Module (Battery not included

IC Extractor is ideally suited for the hobbyist and lab engineer alike. It extracts all DIP IC devices from 8 to 40 Pins. One piece metal construction.

A printed circuit board (PCB) is a flat board made of a non-conductive substrate with conductive copper tracks, pads, vias and components mounted by solder or surface-mount technology; it forms the backbone for wiring, supports active and passive electronic parts, carries signals, power, and connects everything together in nearly all modern electronics.

Taking quality as our principal concern, we are affianced in presenting Read Only Memory. Offered product is appreciated for their unmatched quality and strength. Features: Precisely engineeredReliable in workQuality testedLess maintenanceSturdy

Circuit Device

Siddhi Electronics

IC Extractor

Additional detailed cost componentization of capital equipment that creates the support needed for IFRS and re-classification of assets into more accelerated depreciation/personal property tax categories.

We provide high quality integrated circuit (electronic components )

Clamping Devices To Integrate The Glass Frame

Integrated Circuit Device

Fire Alarms Circuit System

Integrated Circuit Devices ( all types ):

Circuit System