Telemetry Systems And Equipment

This Telemetry radio set allows you to link to a flight controller such as our Ardupilot Mega 2.6 or Multiwii AIO via a USB equipped device such as a computer, laptop or tablet supporting a USB connection (OTG). The Radio set not only lets you see live data such as live GPS position overlaid on a map (if the flight controller has the GPS option) to system voltage, heading, waypoint navigation even artificial horizon and so much more, using open source MAVlink based ground station software

Established as a Sole Proprietorship firm in the year 2019 at Ahmedabad (Gujarat, India), we Umiya Infotech are a leading Wholesale Trader of a wide range of Liquid Flow Meter, Water Flow Meter, Electromagnetic Flow Meter, etc.

Track Real Time Level Presuure Levels of all Cryogenic Tanks on one Platform.

3DR Radio Telemetry Kit 433MHz 500mW The 3DR Radio Telemetry Kit has a 433Mhz frequency band and Receiver sensitivity to -124 dBm. This 3dr telemetry kit allows you to link to a fli

OverviewMicoAir-WiFi-Link is a dual-band (2.4GHz / 5GHz) WiFi 6 telemetry module designed specifically for wireless flight controller tunning and multi-drone swarm light show networking. Powered by OFDMA and downlink MU-MIMO technologies, it provides highly efficient concurrent transmission, ensuring more reliable wireless connections for multi-device networks. Typical ApplicationsMicoAir-WiFi-Link is ideal for the following scenarios: Open-source Flight Controller (ArduPilot/PX4) Wireless Tunining: Supports Ground Control Station (GCS) software such as Mission Planner, QGroundControl (QGC), and MicoPilot. Drone Swarm Light Show Networking: Enables multi-drone swarm communication, waypoint data, and command upload (supports Skybrush). Robotics and Unmanned Systems Wireless Access: Suitable for various control and debugging scenarios requiring short-range, high-bandwidth wireless communication. Product Features Powered by ESP32-C5 Dual-band WiFi: 2.4 GHz / 5 GHz Supports WiFi 6 (802.11ax), backward compatible with 802.11 a/b/g/n/ac Defaults to AP mode for direct connection Supports STA mode for connecting to a router Supports bidirectional Serial - UDP transparent transmission BLE serial transparent transmission (Bluetooth connection currently only supported by MicoPilot) Built-in web-based configuration page Parameter configuration via USB serial AT commands Firmware upgrade via MicoAssistant Parameters Main Controller: ESP32-C5 Wireless Standard: WiFi 6 / 802.11ax, backward compatible with 802.11 a/b/g/n/ac Frequency: 2.4 GHz / 5 GHz Communication Interface: LVTTL (3.3V) Serial / USB-Type-C (CH340) Core Functions: WiFi UDP Serial Transparent Transmission / BLE Serial Transparent Transmission (BLE currently only supported by MicoPilot) Default WiFi Mode: AP (Can be switched to STA mode via AT commands) Max Range (AP Mode): 100 meters (Direct connection to phone/PC, tested in open environments without interference) Max Range (STA Mode): 500 meters (Relayed via high-power router, tested in open environments without interference) Max Range (BLE): 10 meters Operating Voltage: 5V Avg. Operating Current: 150mA Serial Port Debug Port Baud Rate: 115200 Telemetry Port Baud Rate: 57600 / 115200 (Default) / 230400 / 460800 / 921600 Note: The default telemetry port baud rate is 115200. The connected flight controller serial port must be configured to the same baud rate for proper communication. Default Network Parameters AP SSID: MicoAir_WiFi_Link_XXXX AP Password: 12345678 AP Gateway: 192.168.4.1 STA Local IP: 192.168.1.101 STA Target IP: 192.168.1.2 STA Gateway: 192.168.1.1 UDP Port: 14550 WiFi Operating Modes AP Mode (Default): The module creates its own WiFi hotspot. The Ground Control Station (PC/Phone) connects directly to it. STA Mode: The module connects to an existing local router. The GCS and the module communicate within the same Local Area Network (LAN). BLE Bluetooth Name: MicoAir_BLE_XXXX Bluetooth Password: None Connection Range: 10 meters Conflict with 2.4G WiFi: Since BLE and 2.4G WiFi share the same physical antenna and channel, they cannot be used simultaneously. The factory default is 5G WiFi (AP Mode) + BLE. If the module is switched to 2.4G WiFi (AP Mode), BLE will be automatically disabled. In STA mode, connecting to a 2.4G router will also automatically disable BLE. Physical Dimensions: 34.5 23.5x6mm Weight: 5.5g (without antenna)