Sequential Batch Reactor in Ambala (सेकेंटिअल बैच रिएक्टर, अंबाला)

Description: A isothermal semi-batch reactor is a semi-closed system with one input stream. It is operated under conditions like Isothermal (Temperature of Reaction Mass remains constant) and perfectly mixed (composition of reaction mixture is uniform throughout). This set-up is used to study a non-catalytic homogeneous reaction under isothermal condition. The set up consists of a Reactor fitted in a constant temperature water bath. Before starting the reaction the reactor is charged with measured quantity of one reactant. From a feed tank another reactant is fed to the reactor. Using a sampling pipette samples can be taken out for analysis after fixed interval. Rotameter is provided to measure the flow of Chemicals. The compressed air is used for circulation of feed. One stirrer is fitted for mixing the reactants in reactor and other is fitted in water bath to keep the uniform temperature throughout in the bath. The temperature of bath can be maintained from ambient to 70 OC with the help of Digital Temperature indicator Cum Controller. Pressure Regulator, Pressure Gauge and Safety Valve are fitted in the compressed air line. Experimentation: To study a second order sponification reaction in a Semi-Batch Reactor. To determine the Reaction Rate Constant. Utility Required: Compressed Air Supply at 2 Bar, 0.25 CFM. Water supply and drain. Electricity-1.5kw, Single Phase. Instruments, Laboratory wares and Chemicals required for analysis as per the system adopted. Technical Detail: Reactor: Material Stainless Steel, Capacity 3 Ltrs. (approx). Water Bath: Material Stainless Steel, Double wall, insulated with Ceramic Wool. Heater: Nichrome wire Heater Stirrer: Material Stainless Steel Impeller and shaft coupled with FHP motor Feed Tank (1Nos.): Material Stainless Steel, Capacity - 20 Ltrs. Feed Circulation: By compressed air. Flow Measurement: Rotameter. Piping: Material Stainless Steel and PVC. Pressure Regulator: 0-2 Kg/cm2 Pressure Gauge: Bourdon type 0-2 Kg/cm2 Stop Watch: Electronic Temp. Sensor: RTD PT-100 type Control panel comprises of: Digital Temp. Controller: 0-199.9 C, RTD PT-100 type (For Water Bath) With Standard make on/off switch, Mains Indicator etc. Instruction Manual: An ENGLISH instruction manual will be provided along with the Apparatus The whole unit is assembled rigidly on a base plate and mounted on a stand. Most of the parts are powder coated and rest are painted with auto paints.

With our years of experience in-depth knowledge in this field, we are engaged in offering a quality-assured array of Isothermal Batch Reactor.

Adiabatic Batch Reactor Description:An adiabatic batch reactor is a closed system with no input and output streams. This reactor is operated under conditions like adiabatic (Temperature of Reaction Mass keep on changing), Perfectly mixed (composition of reaction mixture is uniform throughout), and constant volume (volume of the reaction mixture within the reactor remains constant, there is no appreciable change in the density of reaction mass). This set-up is used to study a catalytic homogeneous reaction under adiabatic condition. The set-up consists of a Dewar flask of capacity 1 lit. fitted with a stirrer. The flask is double insulated by ceramic wool insulation. Temp. is measured by digital temp indicator. The whole setup is mounted on a rigid M.S. frame.Utilities Required:Electricity Supply: Single Phase, 220 V AC, 50 Hz, 5-15 Amp combined socket with earth connection. Earth voltage should be less than 5 volts.Floor Area Required : 1.0 m x 1.0 m.Instruments, Laboratory Glassware and Chemicals required for analysis as per the system adopted. Technical Details:Reactor : Material Stainless Steel, Capacity 1 Ltrs. (Approx)Insulated with Ceramic wool.Stirrer : Teflon Impeller and Stainless Steel shaft coupled with FHP motorControl panel comprises of :Digital Temp. Indicator : 0-199.9 CTemp. Sensors : RTD PT-100 type